Product ID:EA 9430, PART A #AA9231
MSDS Date:05/02/1994
FSC:8040
NIIN:01-124-2842
Kit Part:Y
MSDS Number: CBTTH

DEXTER CORP. DEXTER ELECTRONIC MATERIALS DIV.

ONE DEXTER DRIVE
SEABROCK, NH 03674
US

Emergency Phone: 1-800-424-9300

Info Phone: 603-474-5541

Preparer: KEN DECOSTA

Cage: 1JB33

WATKINS AND ASSOCIATES INC

LILBURN, GA 30047 US

Telephone: 770-279-9200

Cage: 3D523

EPOXY RESIN

CAS: 25068-38-6

RTECS: KC2100000

Fraction By Weight: 70-90%

STYRENE POLYMER

Fraction By Weight: 5-10%

BUTADIENE ACRYLONITRILE COPOLYMER

Fraction By Weight: 5-15%

FIBROUS GLASS

CAS: 65997-17-3

Fraction By Weight: 1-5%

ACGIH TLV: 10 MG/M3

SILICON DIOXIDE (AMORPHOUS)

CAS: 67762-90-7

Fraction By Weight: 1-5%

ACGIH TLV: 6 MG/M3

VOC = <10 G/L ESTIMATE

RTECS: 9999999VO

Fraction By Weight: NA

OSHA PEL NOT RELEVANT

ACGIH TLV: NOT RELEVANT

Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:CAN CAUSE EYE IRRITATION.
PROLONGED/REPEATED CONTACT CAN CAUSE SKIN IRRITATION. CAN BE
IRRITATING TO RESPIRATORY SYSTEM.*EXCESSIVE HEAT BUILDUP W/RELEASE
OF TOXIC GASSES.

First Aid:EYES: FLUSH W/WATER 15 MINUTES WHILE HOLDING EYELIDS OPEN.
GET MEDICAL AID. SKIN: FLUSH W/WATER 15 MINUTES. REMOVE
CONTAMINATED CLOTHES. WASH THOROUGHLY W/SOAP & WATER. INHALATION:
REMOVE TO FRESH AIR & PROVIDE OXYGEN IF TROUBLE
BREATHING.INGESTION: IF CONSCIOUS GIVE LARGE AMTS WATER. GET
MEDICAL AID.

Flash Point Method:TOC
Flash Point:>300F,>149C
Lower Limits:NA
Upper Limits:NA
Extinguishing Media:DRY CHEMICAL, HALON FIRE EXTINGUISHER, WATER SPRAY,
FOAM, FOG.
Fire Fighting Procedures:USE SCBA WHEN FIGHTING FIRES IN CONFINED
AREAS.
Unusual Fire/Explosion Hazard:DENSE SMOKE & TOXIC GASES MAY BE
LIBERATED.

Spill Release Procedures:WEAR PROTECTIVE CLOTHING/GLOVES/SAFETY
GLASSES. SCRAPE UP & TRANSFER TO METAL CONTAINER. WIPE UP REMAINING
RESIDUE W/SOLVENT OBSERVING SOLVENT FLAMMABILITY CAUTIONS.

Handling and Storage Precautions:KEEP COOL IN ACCORDANCE W/LABEL
INSTRUCTIONS.
Other Precautions:FOLLOW RECOMMENDED CURING SCHEDULE.

Respiratory Protection:NOT NEEDED W/GOOD INDUSTRIAL VENTILATION.
Ventilation:LOCAL EXHAUST RECOMMENDED
Protective Gloves:IMPERVIOUS PLASTIC OR RUBBER
Eye Protection:SAFETY GLASSES OR GOGGLES
Other Protective Equipment:AS NEEDED TO PROTECT SKIN & CLOTHING.
Supplemental Safety and Health
NK

Boiling Pt:B.P. Text:DECOMPOSES
Vapor Pres:<0.01
Vapor Density:NIL
Spec Gravity:>1.0
Evaporation Rate & Reference:NIL
Solubility in Water:NIL
Appearance and Odor:CREAM PASTE, PUNGENT ODOR
Percent Volatiles by Volume:<0.01

Stability Indicator/Materials to Avoid:YES
STRONG OXIDIZING AGENTS, STRONG LEWIS OR MINERAL ACIDS.
Stability Condition to Avoid:NA
Hazardous Decomposition Products:CO, NOX, ALDEHYDES, ACIDS,
UNDETERMINED ORGANICS.
Conditions to Avoid Polymerization:AVOID MIXING RESIN/CURING AGENTS
>0.5LB. DON'T HEAT MIXED ADHESIVES >75F UNLESS CURING SURFACES TO
BE BONDED.MAY RESULT*

Waste Disposal Methods:DISPOSE OF AS HAZARDOUS WASTE ACCORDING TO
FEDERAL, STATE, LOCAL REGULATIONS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.